Key takeaways
- Compare five thermal pads for GPU memory, VRAM and laptop heatsinks, with conductivity ratings, sheet sizes and thicknesses from 0.5 to 3 mm covered.
When a gaming laptop or graphics card runs hot, the fix is not always a fan or an external cooling pad. Inside the chassis, memory chips, voltage regulators and SSD controllers pass heat to a heatsink through soft thermal pads, which dry out, tear and lose contact over time. Replacing them with fresh pads of the correct thickness is one of the few internal cooling jobs a careful owner can do with basic tools.
The five pads below cover the main shapes of the job: a high-conductivity strip for GPU memory, a mid-size sheet for card work, a soft stackable pad for uneven laptop heatsinks, a multi-thickness pack for trial fitting, and a small square for single-chip repairs. Specs come from the listings and maker data sheets; where a detail was not visible, the specs say to confirm it on the listing. Conductivity figures are maker ratings, and no pad here promises a specific temperature drop.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
For most GPU and laptop repads, start with the GELID GP-Ultimate: its 15 W/mK rating is the highest here and the strip suits memory chips. For a full card, the OwlTree 3-pack covers three thicknesses in large sheets. For uneven laptop heatsinks, the soft, stackable ARCTIC TP-3 forgives imperfect gaps. Measure first, because thickness matters most.
GELID Solutions GP-Ultimate Thermal Pad, 120 x 20 x 1.0 mm
GELID rates the GP-Ultimate at 15 W/mK, the highest conductivity figure in this roundup, making it the natural first look for graphics card memory and VRM repads. The 120 by 20 mm strip matches the long, narrow layout of GDDR memory rows on many desktop cards, and the series also comes in 90 by 50 mm and 120 by 120 mm sheets for broader coverage.
The trade-off is firmness. At a listed hardness of 60 to 70 Shore OO, the GP-Ultimate compresses less than softer pads, so thickness must match the gap closely: too thick and the heatsink sits proud of the GPU die, too thin and the memory chips lose contact. GELID lists it as non-conductive, non-corrosive and non-curing. Buy it when you know your exact thickness and want the strongest rated transfer in a strip.
Specs
- Size: 120 x 20 mm (other sizes in the series)
- Thickness: 1.0 mm (confirm other thicknesses on the listing)
- Thermal conductivity: 15 W/mK (maker rating)
- Density: 3.2 g/cm3
- Hardness: 60 to 70 Shore OO
- Continuous use temperature: minus 60 to 220 degrees Celsius
- Model number: TP-GP04-R-B
Thermalright Extreme Odyssey II Thermal Pad, 85 x 45 x 1.0 mm
The Extreme Odyssey II is Thermalright’s second-generation pad line, and the 85 by 45 mm sheet is sized for graphics card work: large enough to cover a row of memory chips or a VRM section in one piece, small enough to handle without waste. It is sold in thicknesses from 0.5 to 4.0 mm in this size, plus a larger 120 by 120 mm format, so matching an existing thickness is straightforward.
The pad is a non-conductive silicone sheet, which matters around densely packed surface-mount components, and Thermalright lists a breakdown voltage of 9.8 kilovolts for the material. One detail to check: the listing title references the 12.8 W/mK figure of the first-generation Odyssey, while Thermalright rates the Odyssey II material higher, so confirm the rating on the listing for the variant you buy. Choose it for a mid-size sheet with the widest thickness ladder here.
Specs
- Size: 85 x 45 mm (120 x 120 mm also available)
- Thickness: 1.0 mm (0.5 to 4.0 mm range in this size)
- Thermal conductivity: confirm on the listing (Odyssey II rating; title references the earlier 12.8 W/mK figure)
- Material: silicone, non-conductive
- Breakdown voltage: 9.8 kV (Odyssey family figure)
- Hardness: 30 to 55 (Odyssey family figure)
- Model number: EXT-ODYSSEY II 85×45 1.0mm
ARCTIC TP-3 Premium Performance Thermal Pad, 120 x 20 x 1.0 mm, 4 Pieces
The TP-3 takes a different approach from the conductivity race. ARCTIC does not publish a W/mK figure for it; the pad is built around softness. Based on silicone with a special filler, it compresses easily, so a 0.5 mm pad can squeeze to about 0.3 mm and absorb height differences between neighboring chips. That forgiveness is what thin laptop heatsinks need, where one rigid pad can lift the cooler off the chip next door.
ARCTIC also states that TP-3 pads can be stacked without the performance loss stacking usually causes, so two 1.0 mm strips can stand in for a 2.0 mm gap. This four-piece pack suits M.2 SSD heatsinks and memory rows, and the same material comes in larger sheets. The pad is electrically insulating and non-adhesive, making repositioning during a fiddly teardown less stressful. Pick it when gaps are uneven or uncertain.
Specs
- Size: 120 x 20 mm, 4 pieces (larger sheets also available)
- Thickness: 1.0 mm (0.5 and 1.5 mm also available)
- Thermal conductivity: not stated by the maker
- Stacking: rated by the maker as stackable without performance loss
- Specific gravity: 3.5 g/cm3
- Continuous use temperature: minus 40 to 150 degrees Celsius
- Model number: ACTPD00056A
OwlTree 3 Pack Thermal Pads, 100 x 100 mm, 0.5, 1.0 and 1.5 mm
The OwlTree 3-pack solves the most common repad problem: not knowing the thickness you need until the card or laptop is already open. One pack carries a 100 by 100 mm sheet in each of 0.5, 1.0 and 1.5 mm, so you can compare against the old pads on the bench and cut the match with scissors. OwlTree rates the material at 12.8 W/mK, level with the first-generation Odyssey figure, and the sheets suit heatsinks across laptops, GPUs, SSDs and smaller board components.
A 100 by 100 mm sheet goes a long way: a full graphics card memory and VRM layout can usually be cut from one sheet with offcuts left for an SSD. The listed density is 3.1 g/cc with a hardness of 30 to 55, a medium-soft class similar to the Odyssey pads. Buy it when a machine is already apart and guessing one thickness in advance feels risky.
Specs
- Size: 100 x 100 mm per sheet
- Contents: 3 sheets, one each of 0.5 mm, 1.0 mm and 1.5 mm
- Thermal conductivity: 12.8 W/mK (maker rating)
- Density: 3.1 g/cc
- Hardness: 30 to 55 (scale as listed; confirm on the listing)
- Material: silicone thermal pad, non-conductive per the listing
Thermal Grizzly Minus Pad 8, 30 x 30 x 1.5 mm
Thermal Grizzly’s Minus Pad 8 is the long-running enthusiast standard, built on a ceramic silicone compound with nano aluminum oxide and rated at 8 W/mK. That figure is lower than the GELID and Thermalright ratings above, but the pad compensates with an elastic, adaptable surface that conforms at low contact pressure, suiting delicate laptop boards and console heatsinks. The 30 by 30 mm square in 1.5 mm is a single-job size for a chipset or SSD controller.
The wider series spans three sizes in thicknesses from 0.5 to 3.0 mm, so scaling up to a full card is possible within the same material. Thermal Grizzly lists the pads as electrically insulating, with a V-0 flammability rating. One sourcing note: this variant’s Amazon code was verified on a non-US Amazon storefront rather than the US one, so confirm size and thickness on the listing before ordering. Choose Minus Pad 8 when conformability at low pressure matters more than the biggest conductivity number.
Specs
- Size: 30 x 30 mm (larger sizes in the series)
- Thickness: 1.5 mm (0.5 to 3.0 mm across the series)
- Thermal conductivity: 8 W/mK (maker rating)
- Material: ceramic silicone with nano aluminum oxide
- Hardness: Shore 00-60
- Operating temperature: minus 100 to plus 250 degrees Celsius
- Flammability: V-0
How to choose
Start with thickness, because it decides whether the pad works at all. Measure the old pads with calipers as you remove them and replace like with like. A pad that is too thick holds the heatsink off neighboring components; one that is too thin never touches, and an air gap transfers almost no heat. If the old pads are destroyed, a multi-thickness pack such as the OwlTree set lets you trial-fit on the bench.
Next, match format to the job. Long 120 by 20 mm strips fit memory rows and M.2 heatsinks, mid-size 85 by 45 mm sheets suit VRM sections, and full 100 by 100 mm sheets are the economical route for a whole card. Then weigh conductivity against softness: high W/mK ratings help only when contact is good, so uneven laptop heatsinks often do better with a softer pad, while a flat desktop backplate can exploit a firmer sheet. Finally, confirm the pad is electrically non-conductive, as every pick here is.
Who should skip
Skip thermal pads if your machine is under warranty and opening it would void that warranty. Also skip the job if the hot component is the CPU or GPU die itself: dies use paste, putty or a phase-change sheet, and a pad there makes temperatures worse. If you are not comfortable handling ribbon cables and fragile clips, a repad is not a first project. And if temperatures are high because a fan has failed or the fins are clogged with dust, fix that first.
FAQ
How do I know which thermal pad thickness to buy?
Measure the pads you remove with calipers and replace each at the same thickness. If measurement is impossible, compare against a multi-thickness pack and pick the pad that lets the heatsink sit flat with light compression. One that needs force to seat is too thick; one that slides freely is too thin.
Can I use thermal paste instead of a thermal pad?
Only on the main die, where the gap is near zero. Paste cannot bridge the half-millimeter or larger gaps over memory and VRM components; it pumps out or leaves air pockets. Pads and paste do different jobs, and most cards and gaming laptops use both in different places.
How often should thermal pads be replaced?
Replace them whenever they are torn, dried out or crumbling during a teardown, since a disturbed pad rarely reseats perfectly. In an undisturbed machine, pads commonly last several years. Rising memory junction temperatures are a practical sign the pads are due.
Is a higher W/mK rating always better?
No. The rating is measured under maker test conditions and assumes good contact. A softer, lower-rated pad can outperform a firm high-rated pad on an uneven surface because it fills the gap completely. Thickness accuracy and compression usually matter more than rated conductivity.
Final verdict
For a known thickness and a desktop graphics card, the GELID GP-Ultimate offers the strongest rated transfer in a memory-friendly strip. For uncertain gaps, the OwlTree 3-pack removes the guesswork, and for uneven laptop heatsinks the soft, stackable ARCTIC TP-3 is the forgiving option. The Thermalright Odyssey II covers the middle ground, and the Minus Pad 8 remains the low-pressure conformability pick. Whichever you choose, measure first: the best pad is the one that exactly fills your gap.
Product and ASIN Reference
| Product | ASIN |
|---|---|
| GELID Solutions GP-Ultimate Thermal Pad, 120 x 20 x 1.0 mm | B08MX8QN9T |
| Thermalright Extreme Odyssey II Thermal Pad, 85 x 45 x 1.0 mm | B0CQ53GSBP |
| ARCTIC TP-3 Premium Performance Thermal Pad, 120 x 20 x 1.0 mm, 4 Pieces | B09V52D1N1 |
| OwlTree 3 Pack Thermal Pads, 100 x 100 mm, 0.5, 1.0 and 1.5 mm | B09DC772PR |
| Thermal Grizzly Minus Pad 8, 30 x 30 x 1.5 mm | B00ZJT2ZS2 |
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAs an Amazon Associate we earn from qualifying purchases.




